LOLER, PUWER Or PSSR: Which Regulations Apply To Your Equipment?

Most workplace equipment falls under the Provision and Use of Work Equipment Regulations 1998 (PUWER), because PUWER covers any machinery, appliance, apparatus, tool or installation used at work. Other regulations then add specific duties for particular kinds of equipment: the Lifting Operations and Lifting Equipment Regulations 1998 (LOLER) for anything that lifts or lowers loads, the Pressure Systems Safety Regulations 2000 (PSSR) for systems containing steam or gas under pressure, and the Control of Substances Hazardous to Health Regulations 2002 (COSHH) for local exhaust ventilation. One machine can be covered by several at once, and each asks for something different.

If you would like your equipment list checked against all of them, email it with the site address to info@gsbinspections.co.uk and we aim to come back with a quote within 48 hours.

PUWER: The Baseline For All Work Equipment

PUWER requires work equipment to be suitable for its purpose, maintained (Regulation 5), inspected where it is exposed to conditions that can cause deterioration (Regulation 6), guarded against dangerous parts, fitted with proper controls and isolation, and used by people with adequate information and training. It applies to a lathe, a baler, a conveyor and a forklift alike.

Regulation 6 sets no fixed interval for general equipment: inspection is due after installation where safety depends on it, at suitable intervals where deterioration could lead to danger, and after exceptional circumstances. The one exception is the power press, which PUWER requires to be thoroughly examined at least every 12 months where only fixed guards are fitted and at least every 6 months in other cases.

LOLER: Extra Duties For Lifting Equipment

If equipment lifts or lowers loads, LOLER applies on top of PUWER. Its central duty, in Regulation 9, is a thorough examination by a competent person:

  • at least every 6 months for equipment that lifts people and for all lifting accessories, such as slings, chains and shackles;
  • at least every 12 months for other lifting equipment;
  • or at the intervals set in an examination scheme;
  • and before first use (unless new with a valid declaration of conformity), after installation at a new site where safety depends on it, and after exceptional circumstances.

PUWER’s Regulation 6 inspection duty does not apply to lifting equipment, because LOLER’s thorough examination covers it. The rest of PUWER still does: a forklift needs maintaining under PUWER and thoroughly examining under LOLER, and HSE’s guidance treats those as separate jobs.

PSSR: Pressure Systems And Written Schemes

PSSR applies to systems containing a relevant fluid, including steam and compressed air. Its core duties are a written scheme of examination drawn up or certified by a competent person before the system is operated (Regulation 8), and examination in line with that scheme with a signed report (Regulation 9). There is no single interval: the scheme sets the limits and each report gives the next date.

Not every compressor is caught. Under Schedule 1, a system holding a relevant fluid other than steam is outside the scheme, examination and record duties where every pressure vessel in it is under 250 bar litres, that is the pressure in bar multiplied by the internal volume in litres. Steam systems are always in.

COSHH: LEV Thorough Examination And Test

Where local exhaust ventilation (LEV) controls exposure to hazardous substances such as dust, fume or vapour, Regulation 9 of COSHH requires it to be thoroughly examined and tested at least once every 14 months, or more often for the processes listed in Schedule 4, with records kept for at least five years.

Equipment That Falls Under More Than One Regulation

Overlaps are normal. Some common examples:

  • Forklift truck: PUWER for maintenance and safe use, LOLER for the thorough examination of the mast, chains, forks and attachments.
  • Compressor and air receiver: PUWER for the machine, PSSR for the receiver and its protective devices where the 250 bar litre threshold is met.
  • Woodworking machine with dust extraction: PUWER for guarding and controls, COSHH for the LEV examination and test.
  • Vehicle lift in a workshop: PUWER for maintenance, LOLER for the 12-monthly thorough examination.
  • Steam boiler in a laundry or food plant: PSSR for the written scheme and examination, PUWER for the machinery around it.

Where one examination already covers the significant risks of an item, it can satisfy the PUWER Regulation 6 inspection duty for that item, so it should not be paid for twice.

Which Regulation Applies? A Quick Check

  1. Is it used at work? Then PUWER applies.
  2. Does it lift or lower loads, or is it a lifting accessory? Add LOLER.
  3. Does it contain steam, or compressed gas in a vessel of 250 bar litres or more? Add PSSR.
  4. Does it extract dust, fume or vapour to control exposure? Add COSHH LEV testing.
  5. Is it a power press? Add the PUWER power press examinations.

Equipment Regulation Questions

Does LOLER replace PUWER for lifting equipment?

No. LOLER adds duties for lifting equipment, but PUWER still applies. Only PUWER’s Regulation 6 inspection duty is disapplied, because LOLER’s thorough examination covers it.

Is a PUWER inspection the same as a LOLER thorough examination?

No. A LOLER thorough examination is a set legal requirement with fixed maximum intervals and a prescribed report. A PUWER inspection is a risk-based check at intervals suited to the equipment.

Does every air compressor need a PSSR written scheme?

No. Systems other than steam fall outside the scheme and examination duties if every pressure vessel is under 250 bar litres.

How often does LEV need testing?

At least once every 14 months under COSHH Regulation 9, or more often for the processes listed in Schedule 4.

LOLER, PUWER And PSSR Inspections On One Visit

We carry out LOLER inspections, PUWER risk assessments and PSSR inspections, so lifting equipment, work equipment and pressure systems on the same site can be covered in one planned visit, each with its own report. We examine and report only, with no equipment, parts or maintenance to sell, and five engineers covering anything from a single item to multi-site contracts across the UK.

Email the equipment list and site address to info@gsbinspections.co.uk, or call 01782 855481 to talk it through with one of the two directors, both senior engineers; we will still ask for the list in writing. We aim to come back with a quote within 48 hours. GSB Inspections is a SAFed associate member.

About Us

We’re independent engineering inspection company covering the whole of the UK, trusted by over 500 businesses to keep their LOLER, PUWER, PSSR and LEV inspections on track.

Inspections are all we do. We don’t repair, service or sell equipment, so you get a straight, impartial report every time.

Our inspections are overseen by directors who are Chartered and Incorporated Engineers, and backed by a team that’s quick to quote, easy to reach and keeps things moving from first enquiry to final report. It’s why our customers rate us five stars on Google.

We’re Here to Help

Get a FREE Engineering Inspection quote now…

SAFed Associate Member badge

Associate Member Of The Safety Assessment Federation (SAFed)

As an associate member of the Safety Assessment Federation (SAFed), GSB Inspections demonstrates our commitment to complying with industry competency standards and the code of practice set by SAFed. This affiliation emphasizes our dedication to maintaining the highest levels of professionalism, ensuring your safety and peace of mind.

Recent Posts

What Our Customers Say

  • My first contact was with Gary and he dealt with my query and questions brilliantly. He explained the process, it was easy to sort and it went smoothly. Expected contact... read more

    Mrs B
    December 8, 2023
  • Excellent service & communications

    Gary Jackson
    October 8, 2023
  • Been using GSB for a year, great service keeping all our plant and machinery in certification

    James Plant
    September 8, 2023
  • Service, communication, support and advice has been excellent, Garry has gone out of his way to support our school with issues arisen from council maintenance, he has gone out of... read more

    Miss H Morrey
    July 13, 2023
  • Well what a great service Gary provides, always does a very thorough job, can't recommend enough, we always Gary really great guy.

    Daz Griffiths
    May 19, 2023
  • Inspected transferable winch units with, greatly appreciated, additional guidance covering separate requirements for accompanying D shackles and inspection schedule. Very diligent service and great value.

    Andrew Piekarczyk
    March 19, 2023
  • Excellent service very competent knowledgeable and professional staff Would highly recommend

    Carl Eades
    January 19, 2023
  • Great service. Would highly recommend and will use again.

    Jade Furey
    November 19, 2022
  • Gary has been doing our certifications for the last few years. Very professional and very reliable. A**

    Rob Scanlan
    September 19, 2022
  • Great bloke, reliable, informative, pleasure to deal with.

    Gary Jackson
    September 19, 2022

Get Your FREE Engineering Inspection Quote

No middle person, direct contact, fast turnaround.

Please complete the form below to submit your enquiry and one of our team will get back to you. 

info@gsbinspections.co.uk

Quick Reply

Have any questions?​

01782 855481

Usual working hours

Mon-Fri, 8am until 4pm